Key Specifications
Capacity
30-50 t/h
Engine
36-43 kW
Feed Size350 mm(13.8 in)
Jaw Size700×400 mm(27.6×15.7 in)
Weight3.5 tons
TypeTrailer/Jaw
The UTC604 is a portable trailer-mounted jaw crusher for contractors who move between sites - tow it behind a truck and start crushing within minutes of arrival.
Rated capacity reaches 30-50 t/h, driven by a 36-43 kW diesel engine. Up to 350 mm of feed such as reinforced concrete, brick, asphalt and river stone is reduced to reusable aggregate.
Trailer crushers keep capital cost and site setup time low, which makes them a natural fit for rental fleets and municipal recycling yards. Remote-controlled operation, tracked mobility and a 12-month warranty are standard on every UPSEN machine, with EU conformity documentation and OEM spare parts support for customers in 80+ countries.
Contact us for a detailed quotation and specifications sheet.
Send InquiryTell us your project · We respond within 24 hours
The UPSEN UTC604 is a trailer-mounted jaw crusher built for continuous duty in quarrying, concrete recycling and demolition work. Its rated output is 30-50 t/h, fed from a — hopper and taking material up to 350 mm at the inlet.
The unit travels as one load on a low-bed trailer — — and 3.5 tons — and is driven by 36-43 kW, so no site power supply is needed. Steel tracks let the operator reposition the plant as the working face advances.
When specifying a trailer-mounted jaw crusher, always match the throughput of the crusher with the downstream screening and stockpiling equipment, and check the maximum feed size against the material you actually run. An oversized inlet wastes fuel; an undersized one causes bridging and blocked jaws.
| Model | Capacity | Max. feed size | Total weight |
|---|---|---|---|
| UTC604 (this model) | 30-50 t/h | 350 mm | 3.5 tons |
| UTC503 | 10-30 t/h | 250 mm | 5,500 kg |
| UHC600 | 20-40 t/h | < 300 mm | 3.8 tons |
| UIC80 | 30-150 t/h | 500 mm | 24,000 kg |
Based on rated capacity, the following UPSEN units are usually specified together with the UTC604:
Rated capacity is 30-50 t/h. Actual output depends on the material, the feed size and the discharge setting.
The UTC604 accepts material up to 350 mm.
3.5 tons, transport size — It can be moved on a standard low-bed trailer without dismantling.
36-43 kW.
Yes — UPSEN machines are supplied with EU conformity documentation and leave the factory ready for work. Delivery is by sea (container or flat rack) to major ports.
Payment is 30% T/T deposit with the balance paid before shipment; an irrevocable L/C at sight is also accepted. Quotations are FOB Qingdao and valid for 30 days. Lead time is 15 days for standard models and 30 days for customised configurations, counted from receipt of deposit. The complete machine carries a 12-month warranty from commissioning, and wear parts such as jaw plates carry 6 months with a typical service life of 800-1,200 hours depending on the feed material. Full terms are on our trade terms and service.
Yes. The TC604 is named in the ECM Mark certificate 0P250820.HFIQW55 and the ICR Polska noise verification ICR/VC/UA260915. You can download the original documents from our certifications and compliance page.
Yes. On-site installation, commissioning and operator training are available. Travel and accommodation are charged at cost and there is no separate service fee. Tell us the site location and we will estimate the number of days.
A single tracked unit rarely does everything — pair the UTC604 with the equipment below to build a working line.
Quality & compliance: ISO 9001:2015 quality management · EU conformity documentation verified by three independent bodies · EN ISO 3744:2010 noise tested, LWA 91 dB(A)
