Key Specifications
Capacity
20-150 t/h
Engine
Electric 110 kW
Feed Size750 mm(29.5 in)
Hopper4.0 m³
Length8.5 m
Output< 100 mm(< 3.9 in)
Power110 kW
ShaftDouble Shaft
Weight12 tons
TypeSkid-Mounted/Electric
The UFS750 is a tracked mobile shredder that uses low-speed, high-torque twin-shaft cutting to reduce bulky, tough and metal-bearing waste into recyclable fractions.
It processes C&D waste, wood and biomass, municipal solid waste and, depending on model, scrap metal and end-of-life vehicles - rated up to 20-150 t/h. A Electric 110 kW engine provides the drive power. Operating weight is about 12 tons.
Output size is set by the screen configuration, and an optional over-belt magnet recovers ferrous metal from the output - the first step of any metal recycling line. Remote-controlled operation, tracked mobility and a 12-month warranty are standard on every UPSEN machine, with EU conformity documentation and OEM spare parts support for customers in 80+ countries.
Contact us for a detailed quotation and specifications sheet.
Send InquiryTell us your project · We respond within 24 hours
The UPSEN UFS750 is a tracked mobile shredder built for continuous duty in quarrying, concrete recycling and demolition work. Its rated output is 20-150 t/h, fed from a 4.0 m³/hopper and taking material up to 750 mm at the inlet.
The unit travels as one load on a low-bed trailer -8.5 m and 12 tons -and is driven by Electric 110 kW, so no site power supply is needed. Steel tracks let the operator reposition the plant as the working face advances.
When specifying a tracked mobile shredder, always match the throughput of the crusher with the downstream screening and stockpiling equipment, and check the maximum feed size against the material you actually run. An oversized inlet wastes fuel; an undersized one causes bridging and blocked jaws.
| Model | Capacity | Max. feed size | Total weight |
|---|---|---|---|
| UFS750 (this model) | 20-150 t/h | 750 mm | 12 tons |
| UMS250 | -/td> | 1200×500 mm | 18,000 kg |
| UMS750 | -/td> | 5100×300 mm (Hydraulic lifting) | 28,000 kg |
| UMS950 | -/td> | 2000×500 mm | 49,000 kg |
Based on rated capacity, the following UPSEN units are usually specified together with the UFS750:
Rated capacity is 20-150 t/h. Actual output depends on the material, the feed size and the discharge setting.
The UFS750 accepts material up to 750 mm.
12 tons, transport size 8.5 m. It can be moved on a standard low-bed trailer without dismantling.
Electric 110 kW.
Yes -UPSEN machines are supplied with EU conformity documentation and leave the factory ready for work. Delivery is by sea (container or flat rack) to major ports.
Payment is 30% T/T deposit with the balance paid before shipment; an irrevocable L/C at sight is also accepted. Quotations are FOB Qingdao and valid for 30 days. Lead time is 15 days for standard models and 30 days for customised configurations, counted from receipt of deposit. The complete machine carries a 12-month warranty from commissioning, and wear parts such as jaw plates carry 6 months with a typical service life of 800-1,200 hours depending on the feed material. Full terms are on our trade terms and service.
Yes. The FS750 is named in the ECM Mark certificate 0P250820.HFIQW55, the ICR Polska noise verification ICR/VC/UA260915 and the EN ISO 3744:2010 noise test report LTR20260909001. You can download the original documents from our certifications and compliance page.
Yes. On-site installation, commissioning and operator training are available. Travel and accommodation are charged at cost and there is no separate service fee. Tell us the site location and we will estimate the number of days.
A single tracked unit rarely does everything -pair the UFS750 with the equipment below to build a working line.
Quality & compliance: ISO 9001:2015 quality management · EU conformity documentation verified by three independent bodies · EN ISO 3744:2010 noise tested, LWA 91 dB(A)
